This Salvaged Round Table is a super easy build that you can knock out in just a few hours. You can honor the salvaged look, or just go for that clean and simple look of fresh cut lumber- the choice is yours! Either way, make sure you let us see your work!
As with all of our plans, you are building at your own risk and you should have a firm understanding of building in general before you attempt many of our plans (some are easy as pie and perfect for beginners). With that, go forth, have fun, take lots of pictures and share them in a showcase on the site or on social media with the hashtag #builtTDCtuff and we will share our faves! Be sure to tag @thedesignconfidential on Instagram / FB and @thedesconf on Twitter / Pinterest. If you are a blogger and you post about your build, don’t forget to include a link to your post on your showcase here. Don’t forget… for all of our newer plans, clicking on the images will let them expand to enormous sizes with much greater clarity. The older plans may need updating so please let us know if you need one fixed!
- Tape Measure
- Saw – Jig Saw, Circular, Table, or Miter Saw
- Drill
- Multi-Square and Carpenter’s Square
- Sander
- Kreg Jig – if you build frequently, invest in this one.
- Nail Gun
3 – 4×4 at 8’
1/2 Sheet – 3/4” plywood at 4’x4’ (use half a 4’x8’ plywood sheet or 2 pieces of 2’x4’ plywood sheet)
- 2-1/2″ Pocket Hole Screws
- 1-1/4″ Pocket Hole Screws
- 1-1/4″ Wood Screws
- Countersink Drill Bit
- Pocket Hole Plugs – Paint Grade, Pine, Oak – optional
- Clamps
- Safety Gear
- 3/4″ Edge Banding – optional
- Wood Filler
- Wood Glue
- Sanding Supplies
- Paste Wax
- Finishing Supplies
1 – 4×4 at 32-1/4” – Long Lower Support
2 – 4×4 at 14-3/8” – Short Lower Supports
1 – 4×4 at 40” – Long Upper Support
2 – 4×4 at 14-3/8” – Short Upper Supports
4 – 4×4 at 26-1/8” – Table Legs
1 – 3/4” plywood at 48” diameter – Table Top
Before beginning to build, always check in on my site to make sure you have the most up to date set of plans, I occasionally update and change the plans to make the building process easier or to allow for less expensive purchasing of materials! Read through the entire set of instructions and all comments before beginning this project. If you print out or save plans, be sure to check in on my site to be sure you have the most up to date set of plans, as I occasionally update things for ease of building or buying. If you are new to building, read through the GETTING STARTED section and other articles found under the BUILD tab in the menu on my site, it has valuable information about how to get started, tools and techniques. If you are unfamiliar with the finishing process, visit my Finishing school for some tips and tricks for painting like a pro and for special finishing practices. Use glue to secure your joints and Consider Painting or Staining individual sections prior to assembling. This makes the paint application virtually flawless. Coat with a spray on Poly or Wipe on Poly to protect your finish and your piece and it will last for ages. Adhere to all safety standards and guidelines, and be sure you follow safety protocol throughout your build. If you are unsure about whether you are building safely, run a quick online search for the tool or technique you are using, or contact me via email or post to the forum before you move ahead. My contact info can be found in the menu of my site.
Cut the pieces for the Short and Long Lower Supports. With the Kreg jig set for 1-1/2” material, drill pocket holes in each end and on both sides of the Short Lower Supports and the Long Lower Support. Assemble as shown with glue and 2-1/2” Pocket Screws. Make sure that the angled pieces are positioned so their bottoms are longer than their tops (i.e the angle tapers inward as it moves upward).
Cut the pieces for the Short and Long Upper Supports. With the Kreg jig set for 1-1/2” material, drill pocket holes in each end and on both sides of the Short Upper Supports.
With your Kreg Jig set for 3/4″ material, drill pocket holes along the long edge of the Short and Long Upper Supports as shown.
Attach the Short Upper Supports to the Long Upper Support as shown with glue and 2-1/2” Pocket Screws. Opposite of the Lower Support Assembly, make sure that the angled pieces are positioned so their tops are longer than their bottoms (i.e the angle tapers outward as it moves upward).
Cut the pieces for the Table Legs. With the Kreg jig set for 1-1/2” material, drill pocket holes on both sides of the top ends of each Table Leg.
Assemble the Short and Long Lower Support assembly and the Short and Long Upper Support assembly to the Table Legs as shown.
Cut the piece for Table Top as shown. Apply Edge Banding to the plywood edge if desired. Place on top of the Short and Long Upper Supports as indicated and secure with glue and 1-1/4” Pocket Screws. If you really want to rock the “salvaged” look, be sure to manually distress the Dining Table before finishing it!
Fill any Screw, Nail or Pocket Holes, Sand and Finish as Desired. For Finishing Tips and Tricks visit my Finishing School
// Disclaimer: Some rights reserved. Private use only. Feel Free to link to any of my plans so long as you ONLY use 1 image and provide an ADEQUATE link back to the original source and appropriate plan! Plans from this page are not to be used for commercial purposes or republished without the express written consent of Rayan Turner, The Design Confidential. By accessing or using any part of the web site, you agree to become bound by the terms and conditions of this website as outlined under Terms of Use. If you do not agree to all the terms and conditions of this agreement, then you may not access the Website or use any services. The information contained in this website is for general information purposes only. The information is provided by The Design Confidential.com and while we endeavor to keep the information up to date and correct, we make no representations or warranties of any kind, express or implied, about the completeness, accuracy, reliability, suitability or availability with respect to the website or the information, products, services, or related graphics contained on the website for any purpose. Any reliance you place on such information is therefore strictly at your own risk. In no event will we be liable for any loss or damage including without limitation, indirect or consequential loss or damage, personal injury or death, or any loss or damage whatsoever arising from loss of information or profits arising out of, or in connection with, the use of this website. I hope to provide accurate plans, however, I cannot guarantee each plan for accuracy. Not every plan that I post has been built and tested, so you are building at your own risk. It is recommended that you have a clear understanding of how the project works before beginning any project. Please contact me if you find an error or inaccuracy so that I might fix it. The Design Confidential.com is inspired by but does not replicate exact designs, any similarities between these plans and items sold at specialty retailers is coincidental and not endorsed by or related to any said retailers. // Affiliate links are used for tools and materials. The Design Confidential will earn a small commission for any items purchased using these links. Thank you for your support – every little bit counts!
