Another project request checked off the list, and a fabulous addition to the Clark & Addison Collection! An easy and budget friendly build, this one can be tackled by the most beginner builder!
Showcase: Built From These PlansI am so honored each and every time one of you fine friends builds from these very plans! If you have built this piece, please take a moment and showcase your build! We are dying to see your fabulous hard work!
$50-$75
- Tape Measure
- Square
- Sander
- Drill
- Saw – Optional if you have your local lumber supply cut your boards.
- Kreg Jig – Optional
- 2 – 1×6 at 10′
- 2- 1×6 at 8′
- 5 – 1×6 at 6′
- 2 – 2×3 at 6′
- 5 – 1×3 at 10′
- 2 – 1×3 at 6′
- 2 – 1×2 at 8′
- 1 1/4″ Pocket Hole Screws – if using a Kreg Jig
- 1 1/4″ Wood Screws
- 2″ Wood Screws
- Wood Glue
- Wood Filler
- Sandpaper
- Finishing Supplies
- 7 – 1×6 at 60 1/2″ (Headboard, Foot board Panel) – A
- 2 – 1×6 at 82 1/2″ (Side Rails) – B
- 2 – 1×6 at 59″ (Front and Back Bed Frame) – C
- 2 – 1×3 at 47 1/4” (Headboard Legs) – D
- 2 – 1×3 at 15 1/2″ (Footboard Legs) – E
- 10 – 1×3 at 59″ (Slats) – I
- 2 – 2×3 at 47 1/4″ (Headboard Legs) – F
- 2 – 2×3 at 15 1/2″ (Foot board Legs) – G
- 2 – 1×2 at 81″ (Side Rails Cleats) – H
Before beginning to build, always check in on my site to make sure you have the most up to date set of plans, I occasionally update and change the plans to make the building process easier or to allow for less expensive purchasing of materials! Read through the entire set of instructions and all comments before beginning this project. If you print out or save plans, be sure to check in on my site to be sure you have the most up to date set of plans, as I occasionally update things for ease of building or buying. If you are new to building, read through the GETTING STARTED section and other articles found under the BUILD tab in the menu on my site, it has valuable information about how to get started, tools and techniques. If you are unfamiliar with the finishing process, visit my Finishing school for some tips and tricks for painting like a pro and for special finishing practices. Use glue to secure your joints and Consider Painting or Staining individual sections prior to assembling. This makes the paint application virtually flawless. Coat with a spray on Poly or Wipe on Poly to protect your finish and your piece and it will last for ages. Adhere to all safety standards and guidelines, and be sure you follow safety protocol throughout your build. If you are unsure about whether you are building safely, run a quick online search for the tool or technique you are using, or contact me via email or post to the forum before you move ahead. My contact info can be found in the menu of my site.
Build your Headboard. Use your pocket hole system to join the Head board rails to the inner Legs and your 1 1/4″ pocket hole screws. If you aren’t using a pocket hole system, simply fasten your rails to the inner leg using a countersink bit and 2″ screws.
Fasten the Outside Leg to the Inner Leg. Fasten from the inside of the leg, use glue and 2″ Screws. Build the foot board in the exact same manner, place the rail 1/4″ back, from the front of the Legs and will sit 1 1/2″ from the back of the front legs.
Build the Bed Frame. Just as for the twin size, the Front and Back of the Frame will sit inside the side rails. Fasten the frame together using glue and 2″ screws, then fasten the cleat to the side rails using glue and 1 1/4″ screws. The bottom of the cleats and the supports will sit flush with the bottom of the side rails. Fasten the Frame to the Headboard and Foot Board. The top of the Frame should be fastened at 15″ from the ground or the bottom of the Headboard and Foot Board Legs. Fasten using 2″ screws to the legs, the Headboard, and the Foot Board rails that it will sit against.
Cut your slats and fasten in place using 1 1/4″ screws. They should be spaced approximately 4-6″ apart.
Fill any Screw, Nail or Pocket Holes, Sand and Finish as Desired. For Finishing Tips and Tricks visit my Finishing School
If you enjoyed this post PLEASE PIN IT! Definitely comment below, Share it or Like it, and subscribe to my feed to stay up to date!
You can now also: Follow my blog with blog lovin!
I would love for you to check out my other site: Handmade-Holiday! For all of your DIY Holiday Decor, Gifts, Parties, and More!
**Disclaimer: Some rights reserved. Private use only. Feel Free to link to any of my plans so long as you provide an adequate link back to the appropriate post! Plans from this page are not to be used for commercial purposes or republished without the express written consent of Rayan Turner, The Design Confidential I hope to provide accurate plans, however, I cannot guarantee each plan for accuracy. Not every plan that I post has been built and tested, so you are building at your own risk. It is recommended that you have a clear understanding of how the project works before beginning any project. Please contact me if you find an error or inaccuracy so that I might fix it.
