As promised… we are back with Part 2 of our Gourmet Kitchen! Part 1 Plans can be found here.
This is the perfect compact kitchen for your little gourmet chefs… I will be posting Cottage Style Kitchen modifications next so stay tuned for a more girlish version!
$25-$50
Safety Gear
Tape Measure
Drill
Saw
Jig Saw
Kreg Jig – optional but recommended
Nail Gun – optional but recommended
1 – 1×8 at 6'
1 – 1×2 at 8' (6' will do but 8' is usually cheaper)
1/4 sheet – 1/2″ ply at 2' x 4'
1/2 sheet – 1/4″ ply
Door Handle or Drawer Pull for Microwave
1″ pocket hole screws – optional only needed if using KJ
1 1/4″ pocket hole screws – optional only needed if using KJ
1 1/4″ wood screws
2″ wood screws – not needed if using KJ
Wood Glue
Wood Filler
Sanding Supplies
Finishing Supplies
5 – 1/2″ ply at 7 1/4″ x 5 3/4″ Plate Rack and Micro Wall
1 – 1/2″ ply at 7 3/8″ x 5 1/2″ Micro Door
1 – 1/2″ ply at 2″ x 5 3/4″ Keypad
2 – 1/2″ ply at 7 1/4″ x 6 1/4″ Side Unit Verticals
2 – 1/2″ ply at 10 1/8″ x 7 1/4″ Side Unit Bottoms
1 – 1/4″ ply at 32″ x 15 1/2″ Back
1 – 1×8 at 32 3/4″ Top
2 – 1×8 at 14″ Sides
2 – 1×2 at 7 1/4″ Base Boards
2 – 1×2 at 7 1/2″ Window Trim
2 – 1×2 at 8″ Window Trim
Before beginning to build, always check in on my site to make sure you have the most up to date set of plans, I occasionally update and change the plans to make the building process easier or to allow for less expensive purchasing of materials!
Read through the entire set of instructions and all comments before beginning this project. If you print out or save plans, be sure to check in on my site to be sure you have the most up to date set of plans, as I occasionally update things for ease of building or buying. If you are new to building, read through the GETTING STARTED section and other articles found under the BUILD tab in the menu on my site, it has valuable information about how to get started, tools and techniques. If you are unfamiliar with the finishing process, visit my Finishing school for some tips and tricks for painting like a pro and for special finishing practices.
Use glue to secure your joints and Consider Painting or Staining individual sections prior to assembling. This makes the paint application virtually flawless. Coat with a spray on Poly or Wipe on Poly to protect your finish and your piece and it will last for ages. Adhere to all safety standards and guidelines, and be sure you follow safety protocol throughout your build. If you are unsure about whether you are building safely, run a quick online search for the tool or technique you are using, or contact me via email or post to the forum before you move ahead. My contact info can be found in the menu of my site.
Construct the Hutch Unit: Fasten the Sides to the top if you are using a Kreg Jig, set for 3/4″ stock and your 1 1/4″ pocket hole screws and glue. If you aren't using a KJ, use 2″ wood screws and glue to secure the top to the sides, just be sure to countersink.
Fasten the Base Boards to the Side Panels either with your Kreg Jig set for 3/4″ stock and your 1 1/4″ pocket hole screws and glue, with your pocket holes placed in the side panels themselves. OR you can use 2″ wood screws and glue to secure from underneath into the Side Panels, be sure to center the base boards and countersink if you aren't using a KJ.
Fasten the Side Units in Place: Use your Kreg Jig set for 1/2″ stock and your 1″ pocket hole screws and glue to fasten in place or your 1 1/4″ wood screws and glue, just be sure to countersink.
Fasten the Microwave Keypad in Place, Then the Interior Wall:
If you are going to give this a fancy finish to resemble buttons and such, I recommend doing this prior to fastening in place. Then fasten in place using either your Kreg Jig set for 1/2″ stock and your 1″ pocket hole screws and glue OR your 1 1/4″ wood screws and glue, just be sure to countersink.
Once the Keypad is in place you can tack on the Wall. Use either your Kreg Jig set for 1/2″ stock and your 1″ pocket hole screws and glue or your 1 1/4″ wood screws and glue, just be sure to countersink.
Hang the Microwave Door: Carve the opening out of the door and hang using a hinge for an inset door (just something simple for this). Leave 1/8″ all the way around the little door.
Fasten the Plate Racks in Place: you can use your Kreg Jig set for 1/2″ stock and 1″ pocket hole screws and glue or you can use 1 1/4″ wood screws and glue, be sure to countersink. Given the proximity of these, it may be easier to simply use wood screws.
The plate racks should be spaced 1 5/8″ apart.
Fasten the Back in Place: Carve out the Window Opening as shown below, and then tack on the back using 1 1/4″ wood screws. The back will overhang the hutch bottom by 3/4″, allowing you to secure it to the Base Unit of the kitchen as well.
Tack on the Window Trim: I would probably just glue these in place, they aren't structural and so should be just fine.
Fill any Screw, Nail or Pocket Holes, Sand and Finish as Desired. For Finishing Tips and Tricks visit my Finishing School
If you enjoyed this post PLEASE STUMBLE IT! Definitely comment below, Share it or Like it, and subscribe to my feed to stay up to date!
You can now also:
**Disclaimer: Some rights reserved. Private use only. Feel Free to link to any of my plans so long as you provide an adequate link back to the appropriate post! Plans from this page are not to be used for commercial purposes or republished without the express written consent of Rayan Turner, The Design Confidential I hope to provide accurate plans, however, I cannot guarantee each plan for accuracy. Not every plan that I post has been built and tested, so you are building at your own risk. It is recommended that you have a clear understanding of how the project works before beginning any project. Please contact me if you find an error or inaccuracy so that I might fix it.
