We covered the Small Hutton Etagere, so how about the Tall? Yes indeed!
Showcase: Built From These PlansI am so honored each and every time one of you fine friends builds from these very plans! If you have built this piece, please take a moment and showcase your build! We are dying to see your fabulous hard work!
$25-$50
Tape Measure
Safety Gear
Drill
Kreg Jig
Saw
8 – 2×2 at 8′
1 – 2×2 at 6′ (if 8′ is cheaper, purchase 9 of those instead of any at 6′)
4 – 1×3 at 8′
1 – 1 x 12 at 8′
1/2 sheet of 3/4″ ply at 4’x 4′
1 1/4″ pocket hole screws
2 1/2″ pocket hole screws
1 pair of Side Mount Drawer Slides
1 or 2 drawer pulls in a style of your choosing
Wood Glue
Wood Filler
Sanding Supplies
Finishing Supplies
2 – 3/4″ Ply at 13″ x 27 1/2″ Top and Bottom of Drawer Casing
1 – 3/4″ Ply at 11 1/2″ x 27 1/2″ Back Drawer Casing
2 – 3/4″ Ply at 11 1/2″ x 13″ Sides Drawer Casing
1 – 3/4″ Ply at 12 3/4″ x 24 3/4″ Drawer Bottom
1 – 1×12 at 27 1/4″ Drawer Front
1 – 1×12 at 24 3/4″ Drawer Back
2 – 1×12 at 12 3/4″ Drawer Sides
27 – 1×3 at 13″ Shelves
10 – 2×2 at 27 1/2″ Front Back Rails
4 – 2×2 at 71″ Legs
10 – 2×2 at 13″ Side Rails
Before beginning to build, always check in on my site to make sure you have the most up to date set of plans, I occasionally update and change the plans to make the building process easier or to allow for less expensive purchasing of materials!
Read through the entire set of instructions and all comments before beginning this project. If you print out or save plans, be sure to check in on my site to be sure you have the most up to date set of plans, as I occasionally update things for ease of building or buying. If you are new to building, read through the GETTING STARTED section and other articles found under the BUILD tab in the menu on my site, it has valuable information about how to get started, tools and techniques. If you are unfamiliar with the finishing process, visit my Finishing school for some tips and tricks for painting like a pro and for special finishing practices.
Use glue to secure your joints and Consider Painting or Staining individual sections prior to assembling. This makes the paint application virtually flawless. Coat with a spray on Poly or Wipe on Poly to protect your finish and your piece and it will last for ages. Adhere to all safety standards and guidelines, and be sure you follow safety protocol throughout your build. If you are unsure about whether you are building safely, run a quick online search for the tool or technique you are using, or contact me via email or post to the forum before you move ahead. My contact info can be found in the menu of my site.
Construct the Side Panels: Use your Kreg Jig set for 1 1/2″ stock and your 2 1/2″ pocket hole screws and glue to secure the rails to the legs. Space the rails as shown below with the top rail flush with the top of the legs, the second and third rails 17″ down, the fourth rail 15 1/2″ down from the third and the bottom rail 2 1/2″ from the bottom of the legs.
Fasten the Front and Back Rails in Place: Use your Kreg Jig set for 1 1/2″ stock and your 2 1/2″ pocket hole screws and glue to secure in place. The spacing will be the same as in the previous step.
Secure the Drawer Casing Sides in Place, then fasten your Drawer Slides in place (if you plan on using them) and finally the Back Drawer Casing: Use your Kreg Jig set for 3/4″ stock and your 1 1/4″ pocket hole screws and glue.
Secure the Top and Bottom of the Drawer Casing in Place: Use your Kreg Jig set for 3/4″ stock and your 1 1/4″ pocket hole screws and glue.
Fasten the Shelf Boards in Place: Use your Kreg Jig set for 3/4″ stock and your 1 1/4″ pocket hole screws and glue to secure the shelf boards in place. The boards should be spaced 1/2″ from the side panel rails and 1/2″ apart.
Construct the Drawer: Fasten the Sides to the Front, the Back to the Sides, and the Bottom to the Front, Sides, and Back. The Bottom is inset in the drawer sides, back and front, while the back is inset between the sides. The Front extends past the sides by 1/2″ on either side.
Fill any Screw, Nail or Pocket Holes, Sand and Finish as Desired. For Finishing Tips and Tricks visit my Finishing School
If you enjoyed this post PLEASE STUMBLE IT! Definitely comment below, Share it or Like it, and subscribe to my feed to stay up to date!
You can now also:
**Disclaimer: Some rights reserved. Private use only. Feel Free to link to any of my plans so long as you provide an adequate link back to the appropriate post! Plans from this page are not to be used for commercial purposes or republished without the express written consent of Rayan Turner, The Design Confidential I hope to provide accurate plans, however, I cannot guarantee each plan for accuracy. Not every plan that I post has been built and tested, so you are building at your own risk. It is recommended that you have a clear understanding of how the project works before beginning any project. Please contact me if you find an error or inaccuracy so that I might fix it.
