This project took me about 30 minutes to complete…that’s it! And 20 of those 30 minutes was spent letting the glue dry while I chatted with you fine friends on Facebook and Google+! Can I get a yahoo? It’s really that simple, and very inexpensive of course, not to mention the possible uses this baby has are utterly endless! I urge you to take a peak a the original inspiration for this piece to see how they have used it. Pretty cool over that table… I decided to use this fine specimen as a fabric storage ladder since space is at a premium in my very small office craft space. The problem I have in this room in particular is that it serves a great many needs without having a great amount of space to do it! Having a place to hang my fabric for upcoming projects is crucial and inspiring since seeing it helps me remember to do those projects and gets those creative juices flowing! Kind of similar to my craft paints and glitter (I am still a gal after all…and I love me some glitter…), having them on display in color coded order is fabulous for my crazy obsessive mind! It’s orderly and beautiful all at the same time!
For the rest of you, this project would be a fabulous addition to any home decor with a rustic reclaimed finish especially this time of year! Can’t you see this with pumpkins all around, corn stalks and scare crows… ah, decor bliss I tell you!
Under $25
Saw – optional, unless you have your local lumber supply make cuts for you. Drill 1″ Spade Bit or Hole Saw Bit.
2 – 2×3 at 8′ 1 – 1″ Round Dowel at 48″ 1 – 1″ Round Dowel at 36″
Wood Glue Sanding Supplies Finishing Supplies Safety Gear
2 – 2×3 at 7′ 5 – 1″ dowel at 15 1/2″
Before beginning to build, always check in on my site to make sure you have the most up to date set of plans, I occasionally update and change the plans to make the building process easier or to allow for less expensive purchasing of materials! Read through the entire set of instructions and all comments before beginning this project. If you print out or save plans, be sure to check in on my site to be sure you have the most up to date set of plans, as I occasionally update things for ease of building or buying. If you are new to building, read through the GETTING STARTED section and other articles found under the BUILD tab in the menu on my site, it has valuable information about how to get started, tools and techniques. If you are unfamiliar with the finishing process, visit my Finishing school for some tips and tricks for painting like a pro and for special finishing practices. Use glue to secure your joints and Consider Painting or Staining individual sections prior to assembling. This makes the paint application virtually flawless. Coat with a spray on Poly or Wipe on Poly to protect your finish and your piece and it will last for ages. Adhere to all safety standards and guidelines, and be sure you follow safety protocol throughout your build. If you are unsure about whether you are building safely, run a quick online search for the tool or technique you are using, or contact me via email or post to the forum before you move ahead. My contact info can be found in the menu of my site.
Cut your ladder legs and rungs: The legs should be 7′ and the rungs (dowels) should be 15 1/2″ each and you will need 5 of those!
Mark and Drill Your Legs: Starting at the top (or bottom) of your legs, mark out 14″ increments. It divides evenly with 7′ so it should work out perfectly. Mark not only at 14″ but also the middle of each board width so that you know where to drill your holes! Tape off your Spade Bit (this is the type I use below and I used blue painter’s tape to mark it) or Hole Saw bit, at about 1/2″ from the bottom of the flat part on a spade bit (not the bottom point) and 1/2″ up from the edge of a hole saw bit. The tape will tell you when to stop drilling so that your hole is only 1/2″ deep. I personally enjoy the spade bit a tad more as I feel like it cuts better and faster, but this is just personal preference, and either will do the job.
Once all of your hole pairs are drilled, you can put a bit of glue in each hole down one board. Pop in your rungs, they should fit perfectly, and then place a drop of glue down the other board in each hole and set that baby right on top of the rungs and lower leg. This should help you put enough weight on the lower leg and rungs and of course the top leg will be supplying it’s on weight. Carefully let it sit like this, or even clamp it (I didn’t) and let the glue set up for 20 minutes or so.
That’s it, you are done! Finish however you prefer. I used a driftwood colored stain on mine, and left all of the markings that were already there. I am not in love with it just yet, and pretty sure it needs a good sanding and another color of stain to really look reclaimed. But, it works for now!
Fill any Screw, Nail or Pocket Holes, Sand and Finish as Desired. For Finishing Tips and Tricks visit my Finishing School
If you enjoyed this post PLEASE STUMBLE IT! Definitely comment below, Share it or Like it, and subscribe to my feed to stay up to date! You can now also: Follow my blog with blog lovin!
**Disclaimer: Some rights reserved. Private use only. Feel Free to link to any of my plans so long as you provide an adequate link back to the appropriate post! Plans from this page are not to be used for commercial purposes or republished without the express written consent of Rayan Turner, The Design Confidential I hope to provide accurate plans, however, I cannot guarantee each plan for accuracy. Not every plan that I post has been built and tested, so you are building at your own risk. It is recommended that you have a clear understanding of how the project works before beginning any project. Please contact me if you find an error or inaccuracy so that I might fix it.
