I believe this piece speaks for itself but just in case it doesn't… This bed is so simple to construct, you will be done in no time! It's also extremely easy on the budget…I see no reason why this couldn't be added to an amazing seating area outdoors as well! If you use outdoor fabric on your pillows or a mattress cover, you will be in business!
$25-$50
- Tape Measure
- Square
- Sander
- Drill
- Saw
- Kreg Jig
- 1 – 2×3 at 6'
- 5 – 2×3 at 8'
- 1 – 2×3 at 10'
- 1 – 2×2 at 6'
- 3 – 1×3 at 10'
- 1 – 1×3 at 8'
- 2 – 1×2 at 8'
- 3″ Screws – for outdoor use, choose either galvanized screws or stainless screws
- 2 1/2″ Screws
- 1 1/4″ Screws
- Wood Glue
- Wood Filler or Paintable Silicone Sealant if being used outside and painted.
- Finishing Supplies or Sealant if for outdoor use.
- 2 – 2×3 at 6 1/2″ (Right hand Legs)
- 3 – 2×3 at 25 1/2″ (Left hand Legs and Center Leg)
- 2 – 2×3 at 75 1/2″ (Front and Back Rails)
- 4 – 2×3 at 34 1/2″ (Stretchers)
- 2 – 1×2 at 75 1/2″ (Cleats)
- 2 – 1×3 at 39″ (End Aprons)
- 9 – 1×3 at 36″ (Supports)
- 1 – 2×3 at 72″ (Front Apron)
- 1 – 2×3 at 29 1/2″ (Back Apron)
- 1 – 2×3 at 40″ (Back Apron)
- 1 – 2×3 at 40 1/2″ (Arm Rest)
- 1 – 2×2 at 45″ (Back Rest)
Before beginning to build, always check in on my site to make sure you have the most up to date set of plans, I occasionally update and change the plans to make the building process easier or to allow for less expensive purchasing of materials! Read through the entire set of instructions and all comments before beginning this project. If you print out or save plans, be sure to check in on my site to be sure you have the most up to date set of plans, as I occasionally update things for ease of building or buying. If you are new to building, read through the GETTING STARTED section and other articles found under the BUILD tab in the menu on my site, it has valuable information about how to get started, tools and techniques. If you are unfamiliar with the finishing process, visit my Finishing school for some tips and tricks for painting like a pro and for special finishing practices. Use glue to secure your joints and Consider Painting or Staining individual sections prior to assembling. This makes the paint application virtually flawless. Coat with a spray on Poly or Wipe on Poly to protect your finish and your piece and it will last for ages. Adhere to all safety standards and guidelines, and be sure you follow safety protocol throughout your build. If you are unsure about whether you are building safely, run a quick online search for the tool or technique you are using, or contact me via email or post to the forum before you move ahead. My contact info can be found in the menu of my site.
Attach the Frame Rails to the inside of the Legs: Leave 3/4″ Space at either end and use 2 1/2″ Screws and Wood Glue. If you plan to take this apart, you can also use Carriage Bolts for this step.
The top of the Frame Rails should be flush with the top of the Shorter Legs and 6 1/2″ from the bottom of the taller legs.
Attach the Stretchers to the Cleats: Use 3″” Screws and Wood Glue.
Then Attach the Cleats to the Frame Rails: Use 2″ Screws and Wood Glue.
Attach the End Aprons: Use 2″ Screws and Wood Glue
Lay the Slats approximately 6″ Apart and screw in place using 1 1/4″ Screws. Do not glue the slats if you plan to remove them at any point.
Â
Attach the Back Rest (Green), then attach the Arm Rest (Red). Use 3″ Screws and Wood Glue.
Then attach the Front and Back Aprons: Use 2″ Screws and Wood Glue.
Fill any Screw, Nail or Pocket Holes, Sand and Finish as Desired. For Finishing Tips and Tricks visit my Finishing School
**Disclaimer: Some rights reserved. Private use only. Feel Free to link to any of my plans so long as you ONLY use 1 image and provide an ADEQUATE link back to the original source and appropriate plan! Plans from this page are not to be used for commercial purposes or republished without the express written consent of Rayan Turner, The Design Confidential I hope to provide accurate plans, however, I cannot guarantee each plan for accuracy. Not every plan that I post has been built and tested, so you are building at your own risk. It is recommended that you have a clear understanding of how the project works before beginning any project. Please contact me if you find an error or inaccuracy so that I might fix it.
