Free DIY Furniture Plans to Build a Wisteria Inspired Reclaimed Pine Entertainment Console. Isn’t this gal a stunner? Yahoo, you should totally build this like right now! Actually you really should because it’s completely stylish and definitely fabulous… so go, and make some sawdust fly my friends… Xx…Rayan
Showcase: Built From These PlansI am so honored each and every time one of you fine friends builds from these very plans! If you have built this piece, please take a moment and showcase your build! We are dying to see your fabulous hard work!
- Tape Measure
- Saw – Jig, Circular, or Miter
- Drill
- Square
- Sander
- Kreg Jig
- 9 – 2×2 at 8’
- 1 – 1×2 at 6’
- 4 – 1×4 at 8’
- 2 – 1×8 at 8’
- 2 – sheets of ¾” plywood
- 1-1/4” pocket hole screws
- 2-1/2” pocket hole screws
- Edge banding for plywood, optional
- Six sets of 14” drawer slides
- Drawer pulls
- Wood filler
- Sandpaper
- Wood glue
- Finishing Supplies
- 4 – 2×2 at 27-1/2” – Legs
- 2 – 2×2 at 81” – Front & Back Frame
- 4 – 2×2 at 26-1/2” – Front & Back Frame
- 12 – 2×2 at 25” – Front & Back Frame
- 3 – 3/4” plywood at 20-1/2” x 25” – Back Panel
- 10 – 2×2 at 14-1/2” – Side Frames & Slide Supports
- 2 – ¾” plywood at 14-1/2” x 20-1/2” – Side Panels
- 1 – ¾” plywood at 14- 1/2” x 78” – Top
- 3 – ¾” plywood at 14-1/2” x 25” – Shelves
- 6 – ¾” plywood at 13-1/4” x 22-1/2” – Drawer Bottoms
- 6 – 1×4 at 13-1/4” – Smaller Drawer Sides
- 3 – 1×4 at 24” – Smaller Drawer Back
- 3 – 1×4 at 24-3/4” – Smaller Drawer Front
- 6 – 1×8 at 13-1/4” – Larger Drawer Sides
- 3 – 1×8 at 24” – Larger Drawer Back
- 6 – 1×4 (ripped to 3” wide) at 24-3/4” – Larger Drawer Front
- 3 – 1×2 at 24-3/4” – Larger Drawer Front
Before beginning to build, always check in on my site to make sure you have the most up to date set of plans, I occasionally update and change the plans to make the building process easier or to allow for less expensive purchasing of materials! Read through the entire set of instructions and all comments before beginning this project. If you print out or save plans, be sure to check in on my site to be sure you have the most up to date set of plans, as I occasionally update things for ease of building or buying. If you are new to building, read through the GETTING STARTED section and other articles found under the BUILD tab in the menu on my site, it has valuable information about how to get started, tools and techniques. If you are unfamiliar with the finishing process, visit my Finishing school for some tips and tricks for painting like a pro and for special finishing practices. Use glue to secure your joints and Consider Painting or Staining individual sections prior to assembling. This makes the paint application virtually flawless. Coat with a spray on Poly or Wipe on Poly to protect your finish and your piece and it will last for ages. Adhere to all safety standards and guidelines, and be sure you follow safety protocol throughout your build. If you are unsure about whether you are building safely, run a quick online search for the tool or technique you are using, or contact me via email or post to the forum before you move ahead. My contact info can be found in the menu of my site.
Cut the pieces for the back frame. Cut the miters in each end of the top piece as well as the top of each leg piece. Set the Kreg jig for 1-1/2” material and drill pocket holes in the mitered end of the legs. Also drill pocket holes in the other pieces as shown. The inside leg pieces will have pocket holes drilled in the top only. Assemble the frame using glue and 2-1/2” pocket hole screws.
Cut the pieces for the back panels. Set the Kreg jig for ¾” material and drill pocket holes in all four edges of each panel piece. Position the each panel in the frame and secure using glue and 1-1/4” pocket hole screws. The back of each panel will be flush with the back of the frame.
Cut the pieces for the sides. Drill pocket holes in all four edges of the panels. Set the Kreg jig for 1-1/2” material and drill pocket holes in each end of the frame pieces. Attach the frame pieces to the panels using glue and 1-1/4” pocket hole screws. The back face of the panel will be flush with the inside face of the frame pieces. Attach the sides to the back legs using glue and 2-1/2” pocket hole screws through the frame pieces into the legs, and 1-1/4” pocket hole screws through the side panels into the back legs.
Cut the pieces for the front frame. Cut the miters in each end of the top piece as well as the top of each leg piece. Set the Kreg jig for 1-1/2” material and drill pocket holes in the mitered end of the legs. Also drill pocket holes in the other pieces as shown. The inside leg pieces will have pocket holes drilled in the top only. Assemble the frame using glue and 2-1/2” pocket hole screws.
Cut the piece for the top. Set the Kreg jig for ¾” material and drill pocket holes in all four edges. Secure to the front frame, sides, and back frame using glue and 1-1/4” pocket hole screws. The top face of the top will be flush with the top faces of the front, sides, and back.
Cut the pieces for the slide supports. Set the Kreg jig for 1-1/2” material and drill pocket holes in each end. The upper supports will be positioned so the top is flush with the top of the corresponding front frame piece. The bottom of the middle and lower supports will be flush with the top of the corresponding frame pieces. Secure using glue and 2-1/2” pocket hole screws.
Cut the pieces for the shelves. Set the Kreg jig for ¾” material and drill pocket holes in all four edges. Secure to the front frame, sides, and back using glue and 1-1/4” pocket hole screws. The top face of the shelves will be flush with the top faces of the front frame.
Cut the pieces for the fronts of the larger drawers. The fronts will be pieced so they look like the smaller drawers. Assemble as shown using glue and 1-1/4” pocket hole screws. Cut the remaining pieces for the drawers. Drill pocket holes in each end of the side pieces as well as all four edges of the bottom. Assemble as shown using glue and 1-1/4″ pocket hole screws. The fronts will overlap the drawer box by 3/8″ on each side. There will be a 1/8” gap around all sides of the drawer fronts in the opening. Install the drawer slides according to the manufacturer’s instructions. For an easy tutorial, click here. Make any necessary adjustments.. Make any necessary adjustments. Install the drawer pulls.
Fill any Screw, Nail or Pocket Holes, Sand and Finish as Desired. For Finishing Tips and Tricks visit my Finishing School
**Disclaimer: Some rights reserved. Private use only. Feel Free to link to any of my plans so long as you provide an adequate link back to the appropriate post! Plans from this page are not to be used for commercial purposes or republished without the express written consent of Rayan Turner, The Design Confidential I hope to provide accurate plans, however, I cannot guarantee each plan for accuracy. Not every plan that I post has been built and tested, so you are building at your own risk. It is recommended that you have a clear understanding of how the project works before beginning any project. Please contact me if you find an error or inaccuracy so that I might fix it.
